Remington 783 Problems: The Remington 783 is a bolt action hunting rifle created by Remington for individuals seeking affordability. It was introduced in 2013 with its name “783” derived from the combination of “3” representing the launch year and “78”, from its predecessor, the Remington Model 788.
Inspired by the Marlin X7 rifle acquired by Remington in 2007 the design of the Remington 783 stands apart from its pricier counterpart, the Remington 700 as they do not share any components.
The performance of the Remington 783 is commendable built upon an accurate design originally pioneered by Savage Arms. This firearm proves to be trustworthy particularly when paired with a barrel. Nonetheless being a product of Remington comes with considerations.
Within this article, we will delve into problems that users may encounter with the Remington 783 and provide solutions for each issue. Moreover, we will incorporate feedback, from users to offer you a comprehensive understanding of this rifle’s capabilities. So be sure to keep an eye out for that!
Specifications & Features of Remington 783
| Specifications | Details |
|---|---|
| Caliber | .270 Winchester, .22-250 Remington, .223 Remington, .243 Winchester, 6.5mm Creedmoor, .308 Winchester, .30-06 Springfield, 7mm Remington Magnum, .300 AAC Blackout, .300 Winchester Magnum, .450 Bushmaster |
| Type | Rifle |
| Place of origin | United States |
| Manufacturer | Remington Arms |
| Produced | 2013–present |
| Mass | 3.4 kg (7.5 lbs) empty without scope |
| Length | 44.5 in (113 cm) in longest version |
| Barrel length | 16.5, 20, 22, or 24 in |
| Action | Bolt action, rotating bolt with 2 lugs |
| Muzzle velocity | Varies (depending on caliber) |
| Maximum firing range | Varies (depending on caliber) |
| Feed system | 3-, 4-, or 5-round detachable box magazine |
| Sights | Variable |
| Capacity | 3/4/5 rounds |
| Finish | Matte |
Common Remington 783 Problems with Solutions
The Remington 783 is a well-known and widely used firearm that has been made for more than a decade. Many people like it because it is reliable and shoots accurately.
However, there are a few problems that can sometimes happen when using it. Let’s talk about these issues, so you are aware of them before you buy the rifle:
- Accuracy Problems
- Ejection/Extraction Issue
- Failure to Feed
- Firing Pin Problem
Problem #1. Accuracy Problems
Remington 783’s accuracy is really bad. When shooting at 100 yards, the bullets group together poorly, with a spread of more than 4 inches. Some Remington 783 rifles perform well, but others don’t.
Solution:
- The problem could be the stock scope. If that’s the case, you should get rid of the stock scope and replace it with a better one. The scope’s eye relief is very limited, which might be fine for a smaller caliber like a 223 but not suitable for a Magnum caliber.
- Additionally, the factory scope is very fragile and made in China. It might even lose a lens after firing about five shots.
Problem #2. Ejection/Extraction Issue
The gun may have trouble properly extracting or ejecting spent casings, even after cleaning and replacing the extractor. Sometimes, even if it extracts properly, it might fail to eject the spent casing.
Solution:
- You might need to use a pocket knife to remove the stuck brass from the chamber. Turn a bronze brush only from the breech end to clean the chamber.
- Sometimes a burned case can get stuck due to slight roughness. In such cases, a patch and solvent won’t be enough. You should use a coiled Tornado brush to polish the chamber.
- If it’s a broken extractor causing the issue, you can replace it with a good one. Make sure to remove all the broken pieces properly before installing the new one.
Problem #3. Failure to Feed
The gun might experience bolt-over-rim failure to feed, which means the magazine feeds rounds to the feed lips with the rim too low to be pushed out by the bolt.
Solution:
This gun is relatively inexpensive, so fiddling with the feed lips might not be the best solution. Instead, try the following:
- Disconnect the plastic floor of the magazine from the metal box. Carefully pry or release the two tiny plastic tabs on each side of the metal box.
- Inside, you’ll find the follower with an accordion spring. Lift the end of the spring resting against the plastic follower’s back at the bottom, below where the rounds are.
- Place a clean penny in the center between the spring and the plastic follower. Use a strong yet somewhat flexible glue to secure the penny in place.
- Be careful not to use too much glue that extends past the follower’s outer edge. The penny only needs to be held in place.
- Once the glue has dried, reassemble everything, and the issue should be resolved.
Problem #4. Firing Pin Problem
The gun fails to fire a shot properly. It leaves a slight indentation on the primer, regardless of the ammunition used.
Solution:
- The firing pin assembly needs to be cleaned, and the bolt should be disassembled. There might be dried grease and carbon causing the problem. Clean the inside of the bolt thoroughly.
- Before reinstalling the firing pin assembly, ensure that there are no protruding pins. The firing pin should protrude by .055″ when de-cocked.
- Check the far end of the bolt tube for any bits of powder, metal, or dried oil. Regularly scrape off any buildup on this shoulder with a flat-bladed screwdriver.
- Also, check if the bolt handle is fully down when closed. Any foreign objects in the action slot, stock, or under the handle in the locking lug area could prevent the firing pin cocking piece from moving forward, causing the issue.
Taurus G3C Problems: Troubleshooting and Fixes
User Reviews for Remington 783 Rifle
Users have shared their thoughts on the Remington 783 rifle, expressing both positive and negative feedback. Remington aimed to establish itself as a manufacturer of affordable, high-quality firearms with the 783 model.
The design of this firearm appears to have been thoughtfully executed and assembled with care. Adjusting it is straightforward, thanks to the Crossfire trigger, which is somewhat similar to the Accutrigger.
The trigger has little to no extra movement before firing, and it breaks smoothly, ensuring a precise shooting experience. When you hold the rifle, you’ll notice it has a substantial weight and feels very robust. The use of polymer material might be simple, but it provides excellent rigidity to the firearm.
Comparing it to the Savage Axis, there are many advantages to the Remington 783. The Stainless variant of the 783 is priced similarly to or even lower than the blued models of other rifles.
One important distinction to make is that the Remington 783 is not at all like the 770 model. Instead, it stands out from competitors like Axis or Ruger American due to its longer 24″ barrels and the availability of two Magnum calibers.
In conclusion, if you’re considering a Remington firearm, it might be worth looking into the old 700 model. However, if you prefer a more budget-friendly option, you should explore the offerings from Savage or Ruger.
Frequently Asked Questions About Remington 783
What scope comes with the Remington 783 rifle?
How does the Remington 700 differ from the Remington 783?
On the other hand, the Remington 783 is magazine-fed, resulting in a more minor ejection port and a more rigid frame.
Who makes the chassis for the Remington 783 long action?
What barrels are compatible with the Remington 783?
These barrels are made to fit Remington 783 actions using the NSS-exclusive Rem/Age barrel nut. Additionally, these pre-fit barrels are carefully hand-lapped, have a polished chamber, and are held to match-grade tolerances, ensuring excellent performance.